Видео

Witam. Imadło super. Jak dobrać się do planów?

Великолепно!

This thing is nice! I have a slow 11.5 second cycle splitter. I need one of these. You build them to sell?

Great video! Talk about over built! Lumber must be much cheaper in Poland than America. That beast would have cost around $1000 in the U.S. Cheers! Świetny film! Mów o przebudowanej! Drewno w Polsce musi być znacznie tańsze niż w Ameryce. Ta bestia kosztowałaby w USA około 1000 dolarów. Pozdrawiam!

Super😀

Nicely done.

WELL, it's spelled well! a weel is wheel but you got it close, spell check would help. lots of lumber, going to cost an arm and a leg? great video

Beautiful work, dude! It looks amazing!!! 😃 Really well done! Stay safe there with your family! 🖖😊

The beers at the end cooling from the earth was a nice touch! Well done :)

Hello guys beautiful project beautifully done good job

MM77 Approved 👍🏼👍🏼

Bardzo udana konstrukcja i to bez hydrauliki. Wszystko mechaniczne i proste w obsłudze.

jeszcze ze dwa kanały załóż i dawaj te same filmy na wszystkich.

I would have used a trailer jack instead of all that fab and carrying a bottle jack. I just picked up a weld on one. Has the round cylinder to Weld to whatever. Then a pull pin to attach or rotate. Has like 28" of travel with side crank handle and drop down leg with pin. $60 weld on and you're done. The pivot makes me jealous though. I picked up a used crane for $150. Cylinder leaks a little, the pivot just a pipe inside another pipe base with gussets. Has a nylon washer between the 2. Cleaning and greasing no has it better but...poor design

Each one gave you. Haug

Who has all that metalworking equipment to begin with? And who has perfect rounds like that? Using this splitter has safety issues. Note how close the operator lets his hands get at times.

Трата времени

You built it very nicely! I would like to make one comment: you have fixed one of the outputs of the differential. With this, you have reduced the ratio by half. It does not cut perfectly because the speed of the cutting roller is low. And the solution is right there in your hands: free the fixed output and simply weld the planetary gears of the differential inside. It will cut beautifully! Very clever!

Hi!! Do you have the project?

Dude; did you streal this footage from Made in Poland, or did he let you use it? Dishonest!!!

Quiero 1 prcio

Great work and fabricator skills new sub

Hardly homemade!!!

.продажей не занимаеша

CESOIA 200 PAEE BATERIE

Cara parabéns pelo trabalho! Importante falar que nada seria possível sem a estrutura presente nessa oficina, e logicamente sem a experiência e talento para usá-la... I am from Brazil

Is there a way to compare it to the tonnage of a hydraulic cylinder to get some kind of idea of what it can do? I really like the seriousness of that splitter but it can be deceiving by the wood you were splitting. One thing for certain is there is no forgiveness if your fingers are in the wrong place. I’m dealing with so much variety with the wood that I split and burn,so I’m more comfortable using my hydraulics. But I can definitely see a purpose in a more perfect world to have and use the one you built. I’m getting old and slightly slower nowadays but I think I might have preferred yours some years back. Thanks for sharing your work ethics, knowledge and build. Peace

Man I’m a retired welder fabricator of over forty years, and I’m putting you up there with me brother. lol. Really nice work. That thing doesn’t play , I would like to see it split some hard oak or maple, just to see what it does. But I have to say, you did a fine job building it. ✌️👍. Oh one more thing, I would love to see it with the shrouds off to see just a bit more. I am impressed for sure. I’ve been doing fab work most of my life. It’s good to see someone else that does the same thing. The few jobs I’ve had working for someone else, when you’re good at this type of thing they always leave you to do your thing. It’s like being your own boss even though you work for someone. I know I drove a lot of people crazy because I don’t ever get yelled at and people do get jealous of the respect I always got. I always enjoyed working because it is something different all the time. Good luck to you brother. ✌️

عمل أكثر من رائع

Todo me perece muy bien,en lo que estoy en desacuerdo es en tener que pagar para unirse al Canal,acaso RUclips no les paga por todos los seguidores Ignoro los procedimientos

Cool but I couldn't buy the raw materials to build one of these for the price I could buy one.

21:25

Συγχαρητήριά για την υπέροχη κατασκευή σου! Από Ελλάδα/Αθήνα.

Can i to know your name?, because i hate to call someone by onomatopoeias. It's not correct and polite.

I ADORE THAT YOU MAKE AND BUILD, I AM SO JEALOUS ABOUT YOU. IT'S SO AND REALLY CLEVER......BRAVO...!!!!

Dobra Robota! :)

Бля ,-убил тещу а из кресма сделал самосвал? Вот это ди ай вайщик ,кремень.

Cum se cheama bara aia de fier care culiseaza si sparge lenmu ca nu gasesc sa cumpar

Are there plans for sale?

Nice job friend. Where can I find those hammer’s blades. What is their size.?

ruclips.net/video/x2ASQ3Uu_cM/видео.htmlsi=gFDGXKxfc3t6uzOm

Brilliant !

Сделай себе ключ для токарного патрона с длинной ручкой

only a Pole can do it because I heard Polish music in the back room, good job, but if you have everything, you can do it. Such a handyman, once again, good job.

Это для "ленивых", ведь можно и топором помахать.

Парень не додумался правильно установить редуктор - что бы на длинной силовой рукоятке, усилие было "от себя", а не наоборот; т.е. бур должен вращаться вправо - "по часовой стрелке". А если бур "левый", то силовая рукоятка должна быть под левую руку.

sehr ordentliche arbeit , ich abe seid gut 35 jahren einen stehend holzspalter hydraulich von posch 6 to spaltkraft auf 230 v finde ich praktischer , liebe grüße aus deutschland

Sei bravo ma la macchina non va . Fai prima con lascia.

Hai fatto un'errore La lama doveva essere a croce con centralina e Pistone idraulico.e Poi non è stabile. troppo lavoro 🤔

Two in one drill and chainsaw cool